You are here: Home / Blogs / The Working Principle and Precautions of Commercial Ice Crusher

The Working Principle and Precautions of Commercial Ice Crusher

Views: 108     Author: Site Editor     Publish Time: 2021-01-15      Origin: Site

Commercial ice crusher machine is also known as ice grinder machine and smoothie ice machine. Ice cube crusher machine is a device that shaves ice cubes into snowflakes. Pour condensed milk and syrup on crushed ice, and mix with various fruits or other ingredients, such as hawthorn slices, raisins, chocolate needles, red bean paste, mung bean paste, ice cream, etc., can be made into high-end cold drinks. These cold drinks have a delicate taste, scumming in the mouth, not much sugar, and an excellent cooling effect. And eating more will not make you feel full. Shaved ice machines are widely used in the catering industry, cold drink shops, western restaurants, coffee shops, casual snacks and hotels, and other industries. It is common cold drink equipment for making iced drinks and can be used to make shaved ice foods with various tastes and flavors.


Working principle of ice crusher


First, break the ice cubes to about 20 mm in diameter, and then put them into the barrel, with the upper edge protruding through the barrel mouth. Turn on the power switch first, and wait until the motor is driven by the power plate to rotate, and then allow the handle of the press cover to be pressed down. At this time, cut the ice cubes by tightening the blades on the rotating cutter head. However, do not use too much force when pressing the handle of the pressing material cover down, so as to avoid the motor blocking and damaging the motor. If it is a fully automatic ice shaver, just put in suitable ice cubes, close the machine cover and turn on the switch. When operating, pay attention to the margin after the ice material is reduced, and add new ice cubes in time.


best ice crusher machine

Precautions for use


  1. When chopped ice particles flow into the tray through the discharge port, pay attention to the smooth discharge of the discharge port, and not be blocked. Otherwise, it will cause the cutter head to jam and burn the motor. If you find that the cutter head is stuck, you should immediately raise the pressing cover handle, turn off the switch, unplug the plug, and troubleshoot in time.

  2. The thickness of the ice particles can be achieved by adjusting the height of the blade protruding from the cutter head. The automatic ice crusher machine for sale only needs to adjust the corresponding thickness switch. If it is semi-automatic, check the instructions for use. Some cannot be opened and adjusted at will. If possible, you need to remove the plastic disk of the protection switch device when adjusting, loosen the screws that fix the elbow, and pull out the barrel. Then loosen the fastening screw of the cutter head, remove the cutter head, and loosen the compression screw of the blade. Install it in place according to the required requirements, and then put the cutter head back in place in order.

  3. The motor design has a transient intercept rate of 80%, so the long-term continuous operation should be avoided. After one hour of continuous work, you should pause for 20 minutes before starting to work again. This will greatly extend the service life of the motor.

  4. After each use, it must be cleaned. When cleaning, turn off the main power switch, unplug the plug, and then wipe the water on the machine with a clean towel.

  5. After cleaning, remember to lift the handle of the press coverage. It is not allowed to use detergent during cleaning to prevent the residual detergent on the machine from causing pollution. It is also not allowed to rinse with water directly, so as to prevent the electrical parts from getting damp, affecting the safe use and damaging the kitchen ice crusher.

  6. Regardless of whether it is cleaning, overhauling, replacing blades or cleaning ice slag, etc., you should turn off the power and unplug the power plug. The electric ice cube crusher is not allowed to run without load for a long time.

Product Category

 TEL:
0086-13505740633 / 0086-18968283993
 ADD:
Rm704, Aux Building, No.757 Rili Middle Road, Yinzhou District, Ningbo, China.



Contact Us
​Copyright 2020 Shionp Industry Co., Limited . Sitemap